Select your vehicle below for: WITHOUT MAF - TinMan Cold-Air Intake Kit # 7483

Specials  
WITHOUT MAF - TinMan Cold-Air Intake Kit # 7483
WITHOUT MAF - TinMan Cold-Air Intake Kit # 7483
Additional
   Images
 
WITHOUT MAF - TinMan Cold-Air Intake Kit # 7483
 
WITHOUT MAF - TinMan Cold-Air Intake Kit # 7483
 
 

$279.95
 
Product Description
 

1986-1987 Buick Turbo Regal -
TinMan COLD-AIR INTAKE KITS

The TinMan Cold-air kit is the “Original” hard pipe cold-air kit for 1986-1987′ Buick Turbo Regals. It’s a 4″ aluminum, mandrel bent, hard pipe kit, which includes a Hi-Flow washable 4″ x 9″ air filter with molded in “velocity stack” neck outlet for the ultimate in airflow. The aluminum elbow has a durable powder-coated finish, available in Satin Black or Silver. High-quality rubber connections help eliminate engine vibration so as not to harm the MAF or MAT sensors.

NOTE - When ordering, be sure to order the correct Part # for the kit designed for the MAF sensor you will be using (factory stock, 3″ LT1, 3.5″ LS1, or no MAF at all for aftermarket ECM’s), so you are shipped the correct kit.

The TinMan kits install without any cutting, drilling or extra brackets, and will even allow you to keep the fuel vapor canister in it’s the stock location.

Filter inlet air temps will run within approximately 1 degree of outside temps!

The TinMan Cold-Air Kit has been flow-bench tested to flow well over 1,200 cfm!

To date, it has also gone 9.20’s in the 1/4 mile at near 150 mph!

Horsepower gains average from 10 hp to as much as 30 hp+, depending on which air intake system you are replacing and level of engine build-up.

These intake kits work very well on “factory stock” as well as heavily-modified Turbo Regals.

The TinMan Cold-air kit includes all parts needed to install, attaching to the MAF sensor and running to the included washable, high-performance air filter. The kit comes complete with installation instructions.


NOTE - When ordering, you MUST specify if you want the elbow section to be powder-coated “BLACK” or “SILVER.” The long pipe is powdered-coated satin black on ALL the applications, since it is not seen under the hood once the kit is installed.

NOTE - When order this part #7483 you MUST tell us the diameter of your car’s mass air pipe to the turbo - 3″ or 4″.


Here are the 4 options for these kits. We have highlighted in RED the one you are ordering if you order through this particular page.

7480 - 1986-1987 Buick Turbo Regal -
FACTORY STOCK MAF - TinMan Cold-Air Intake Kit - Specify SATIN BLACK or SILVER Elbow

7481 - 1986-1987 Buick Turbo Regal - 3″ LT1 - TinMan Cold-Air Intake Kit - Specify SATIN BLACK or SILVER Elbow

7482 - 1986-1987 Buick Turbo Regal - 3.5″ LS1 - TinMan Cold-Air Intake Kit - Specify SATIN BLACK or SILVER Elbow

7483 - 1986-1987 Buick Turbo Regal - WITHOUT MAF - TinMan Cold-Air Intake Kit - Specify SATIN BLACK or SILVER Elbow


 
Part # Applications   Sale QTY
7483  Buick Regal T-Type 3.8 1986-1987   $279.95
7483  Buick Regal Grand National 3.8 1986-1987   $279.95
7483  Buick Regal GNX 3.8 1987-1987   $279.95